Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
Do you find yourself hunting for answers about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a new one is additionally a moderately tough project. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old tub as well as position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and set in the brand-new one. Make certain you have certified on your own for the job and also fit trying it. Rather than employing a contractor to take over a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you may need a specialist plumber to make tube links.
This write-up will help you set up a new tub in your shower room if you have actually already purchased a new tub as well as do not require to change the arrangement of your previous supply of water pipelines.
Your tools and material checklist must consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain any water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Before moving on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area between the tap as well as the sink. Safeguard the faucet in place with the maker given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Making use of both wooden boards under its feet, position the tub in the needed position. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; then do the very same for the other tap.
Activate the supply of water as well as check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and additionally check the overflow outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bathtub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last placement.
Preparing for the Setup
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, causing the water to permeate the wall between the bath as well as the tiling, resulting in issues with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the motion experienced when the tub remains in usage. The sealant can crack relatively early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through a good friend on a different blog. Sharing is caring. You never know, you may be helping someone out. Thank you for your time. Come back soon.
Schedule An Appointment Report this page